Figure 4: Section -372: http://www.globenewswire.com/NewsRoom/AttachmentNg/c29a876f-0f24-465e-899f-aad2044bc6fa

Three holes were completed on this section to test the down dip extensions of historical intercepts. The 4 zones of alteration were all intersected in the drilling.
The southern most hole, OAX-17-211, intersected all four zones of mineralization. From 207.20 m the interval averaged 1.15 g/t Au over a width of 20.70 m, including 5.40 m @ 2.03 g/t Au. A 2.70 m interval from 241.30 m assayed 2.17 g/t Au. From 296.90 m a zone of 5.90 m @ 6.29 g/t Au was intersected. Deeper in the hole two intercepts from one zone were intersected. From a depth of 392.00 m, an 8.20 m interval averaged 1.01 g/t Au, while from 409.50 m, a 5.80 m interval averaged 1.29 g/t Au from the lower most zone.

Hole OAX-17-213 was collared from the same location as OAX-17-211 but was drilled at a shallower inclination and returned intercepts for all four zones. From 40.00 m, assays averaged 1.05 g/t Au over 33.50 m, with higher grades from 72.60 m of 6.17 g/t Au over 0.90 m. From 136.00 m depth, a 22.20 m interval averaged 1.04 g/t Au with higher grade interval from 136.00 m of 2.56 g/t Au over 3.70 m. The average gold value from 175.10 m to 183.00 m for the third zone was 1.51 g/t Au over 7.90 m. The hole intersected tuff to 207.00 m depth and sediments below 207.00 m. Within the sediment unit the hole intersected 6.60 @ 1.06 g/t Au from 211.70 m depth within the fourth zone. This intersection occurred below the contact with the tuff unit.

Drill hole OAX-17-236 was collared in the sediment unit, approximately 37 m north of the two above holes. From a depth of 147.00 m, 1.03 g/t Au was intersected over 9.00 m from the third zone. Deeper in the hole, 1.22 g/t Au over 7.50 m from the fourth zone was intersected from 163.50 m. Included in this interval was 1.56 g/t Au over 4.20 m from 163.50 m. From 208.50 m, 1.96 g/t Au was intersected over 3.00 m. The intersections in the sediments are generally lower grade than in the tuff unit but are significant in that they are north of the tuff and increase the width of the gold zone.

Section -537 (DDH OAX-17-201)

Figure 5: Section -537: http://www.globenewswire.com/NewsRoom/AttachmentNg/8300456b-948d-436a-aedf-95a82b2e177f

Drill hole OAX-17-201 was drilled some 100 m west of the previous resource estimate at Orenada Zone 2. The hole was oriented steeply dipping to the south and collared in the sediment unit. The hole intersected the Cadillac Break and finished in the volcanic rocks. The hole intersected two significant zones of mineralization within the sediment unit but possibly drilled down one zone. From 18.00 m to 37.50 m the zone averaged 3.79 g/t Au over 19.50 m including an interval of 5.12 g/t Au over 8.50 m from 24.50 m to 33.00 m. From 46.50 m to 48.90 m the interval assayed 1.40 g/t Au over 2.40 m. Deeper down the hole, a 27.90 m interval from a depth of 66.50 m averaged 1.95 g/t Au. Within this interval a 10.50 m interval averaged 3.16 g/t Au from 78.00 m. These significant assays occurred in sediments in a near vertical dipping zone of mineralization and extended known mineralization by some 100 m to the west. No significant mineralization was intersected in the tuff. 

Comments

The fourteen drill holes released from the 2017 Orenada drill program extended mineralization to the west by some 100 m and confirmed the existence of four steeply dipping mineralized zones hosting gold bearing quartz-tourmaline veining within the historical resource foot print. The results and interpretation from the drilling will be used in the new resource estimate update which is currently being developed. The new resource will incorporate more geological wireframes and controls on mineralization than the 2009 resource estimate for Orenada.

Table 1. Selected Drill Assay Results: Orenada Zone 2

Lengths are reported as drill core lengths; vertical depth is estimated at 97% of core length. Horizontal thickness of mineralized zones is determined by previous surface and underground holes drilled from the north. Assay intersections are reported using a 0.5 g/t for bulk runs, except where designated “Geological Section” which have no cut-off; 2.0 g/t Au cut-off for the higher-grade veins.  For these reported assays, no internal dilution or top caps are applied: the length of the reported intervals is based on assays and geology.

Orenada Zone 4 and Zone 2 Project Summary

Alexandria’s Orenada project is located at the western end of the Company’s 35 km-long Cadillac Break property package in Val d’Or, Quebec. The property was acquired in 2006 and AZX published a Resource Estimate compliant with National Instrument 43-101in 2009 (See Press Release, September 16, 2009). Since the acquisition of new data in 2015, Company geologists have been re-interpreting the geology of the deposit. With the added information provided by the 2016-2017 drill programs, the Company anticipates a new, updated resource estimate compliant with National Instrument 43-101 in February 2018.

Further information about the Company is available on the Company’s website, www.azx.ca, or our social media sites listed below:

Facebook: https://www.facebook.com/AlexandriaMinerals
Twitter: https://twitter.com/azxmineralscorp
YouTube: https://www.youtube.com/AlexandriaMinerals 
Flickr: https://www.flickr.com/alexandriaminerals/

Analytical Procedures and QA/QC

Program design, management, and Quality Control/Quality Assurance (QA/QC) are conducted by Alexandria’s exploration group under the supervision of Philippe Berthelot (P. Geo), who is the Company’s Qualified Person. Mr. Berthelot has reviewed the results in this press release.

Drill core sampling protocol is conducted according to industry standards, and have been reviewed by the Company’s independent Qualified Person. Half core samples are shipped to AGAT, Bureau Veritas Minerals, or ALS Chemex laboratories for assaying. For visibly mineralized core, the entire core is crushed to 75% passing -2mm (10 mesh); a split of 1 kg of crushed material is then pulverized to more than 85% passing 75 microns (200 mesh). Two pulp samples, 50 g each, are analyzed by Fire Assay (FA) with an Atomic Absorption Spectrometry (AAS) finish. Samples assaying >10.0 g/t Au are re-analyzed with a gravimetric finish on two 50g charges for each sample.

For core samples located between mineralized intersections, the core is crushed up to 75% passing -2mm (10 mesh). A 250g split of this material is pulverized with 85% passing 75 microns (200 mesh); one pulp sample (50 g) is analyzed by Fire Assay (FA) with an Atomic Absorption Spectrometry (AAS) finish.

Commercial certified standard materials and blanks are systematically inserted by Alexandria’s geologists into the sample chain after every 17 core samples as part of the QA/QC program. Duplicate samples are systematically analyzed by the laboratories after every 17 core samples. Third party assays are submitted to other designated laboratories for 5% of all samples.

About Alexandria Minerals Corporation
Alexandria Minerals Corporation is a Toronto-based junior gold exploration and development company with strategic properties located in the world-class mining districts of Val d’Or, Quebec, Red Lake, Ontario and Snow Lake-Flin Flon, Manitoba. Alexandria’s focus is on its flagship property, the large Cadillac Break Property package in Val d’Or, which hosts important, near-surface, gold resources along the prolific, gold-producing Cadillac Break, all of which have significant growth potential.

WARNING: This News Release may contain forward-looking statements including but not limited to comments regarding the timing and content of up-coming work programs, geological interpretations, receipt of property titles, potential mineral recovery processes, etc. Forward-looking statements address future events and conditions and therefore involve inherent risks and uncertainties. Actual results may differ materially from those currently anticipated in such statements. Alexandria Minerals Corporation relies upon litigation protection for forward-looking statements. Neither the TSX Venture Exchange nor its Regulation Services Provider (as that term is defined in the policies of the TSX Venture Exchange) accepts responsibility for the adequacy or accuracy of this release.